![]() ![]() Reboot and check that all 20 USB ports are displayed in Hackintool > USB tab. ![]() Remove your current USBPorts.kext, USBMap.kext or SSDT-UIAC.aml from your /CLOVER/kexts/Other or /OC/Kexts folder, include the corresponding entry in the /OC/ist if required.Įnsure you have USBInjectAll.kext in your /CLOVER/kexts/Other or /OC/Kexts folder, with a corresponding entry in the /OC/ist if required. Remember that the OpenCore XhciPortLimit quirk doesn't work in Big Sur 11.3+ Make sure you have the correct USB port limit patch(es) enabled in your ist, for the version of macOS you are using. Make sure you have the necessary APCI USB rename patches in your ist for EHC1, EHC2 and XHCI. The first thing to do is add the SSDT-EHCx_OFF.aml to your setup, including an entry in the OpenCore ist, assuming you are running your system with OC and not Clover. As you know Apple have limited each USB controller to a maximum of 15 ports, so you need to drop 5 ports to keep within this limit. Your board has a maximum of 20 USB ports. GA-Z97X-UD3H motherboard with USB ports highlighted It runs very well, all works except for the cracking sound which I still unable to solve this issue. ![]() I am currently running macOS Big Sur on my AMD Ryzen 3 3200G series. I think it is a good time to update my AMD Hackintosh system to this latest release. These internal headers are usually used for connecting Case front ports, USB card readers and Bluetooth modules. The new macOS Monterey is now available for public. GA-Z97X-UD3H Rear I/O plate with USB ports highlightedġ x twin USB3 internal header port, providing 2 x USB2 & 2 x USB3 ports (4 ports)Ģ x twin USB2 internal header ports, providing 4 x USB2 ports (4 ports). Your motherboard contains the following USB ports.Ĥ x USB2 ports (black tang) on the rear I/O plate (4 ports).Ĥ x USB3 ports (blue tang) on the rear I/O plate (8 ports) in two groups. This will push all the USB ports from the EHC1/EH01 & EHC2/EH02 controllers to the XHC controller. Your current setup doesn't include any USB2 header ports, so it is likely to be misconfigured.Īdd SSDT-EHCX_OFF.aml to your setup, copy attached. Thanks to trs96, Edhawk and many others for helping this community. Happy that a 2014 computer is still relevant, because of tonymacx86, clover, and open core. So, didn’t even tried.ĭisplay : Benq 1440p monitor is showing with max 1080p resolution only. Double checked the config file, tried fresh install.Īudio : partial. Took the 12.1 usb installer and updated to opencore 0.7.7 debug. 3 os works well.Īnyway, today I saw open core 0.7.7 beta available. Generally, initial OS versions always gave me trouble. Even with 12.1, and tinkering with config file didn’t help. But then it would stop at IOG Flags 0x3 (0x51) / Graphics state error. Using hackintool, I mapped the USB ports, and generated USBPorts kext. I was using USBInstall kext on Big Sur, and it was fine, But not this time. Downloaded Monterey 12.0.1 / open core 7.6 debug, and tried fresh install to another ssd. Otherwise I am quite happy with Big Sur.įirst I updated open core to 0.7.6, and smbios to iMac 17,1 on Big Sur. I wanted to upgrade to Monterey, mainly because of support for AMD RX 6600 XT graphics card, which is the only “reasonably” priced available graphics card for hackintosh. I was running a Big Sur 11.6.1 on iMac 15,1 SMBIOS Building a CustoMac Hackintosh: Buyer's Guide ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |